=========================================================================
V1.3.5.1 - Not yet published
 - Minor bug corrections

=========================================================================
V1.3.5.0 - Not yet published
 - Added TRC298B - Test only

=========================================================================
V1.3.4.1 - Published
 - Added RA-6790 alternate protocol

=========================================================================
V1.3.4.0 - Published
 - Correct a bug in driver selection

=========================================================================
V1.3.3.0 - Published
 - Extended Com. Port. List 
 - Added HF2050 receiver
 - Added RxRmtState() event

=========================================================================
V1.3.2.0 - Published
 - Added RxErrDesc() function

=========================================================================
V1.3.1.0 - Not published
 - Reset the 1792 autopolling mode when exiting

=========================================================================
V1.3.0.0 - Published
 - API changed for Channel processing adding a 'mask' parameter
 - Rx___Count now returns the real type count (and not the max. count)
 - Added MODMAX, AGXMAX, ATTMAX, NBLMAX, SQLMAX & HFFMAX constants which
   return the max value that item can be set to (not including Off state)
 - Thomson TRC294A updated

=========================================================================
V1.2.0.3 - Published
 - Corrects a bug where configuration windows was displayed twice
 - Adds debug information when TRC243 ID cannot be not found
 - Debug "C_Dbg" variable now defaulted to FALSE to avoid creating unused log files

=========================================================================
V1.2.0.2 - Published
 - Error on TRC294 memory mask encoding

=========================================================================
V1.2.0.1 - Internal
 - Mods on drivers settings
 - Provision for TRC243 LINK11 option (not tested)

=========================================================================
V1.2.0.0 - Published
 - Filter type is now LONG
 - Added clock set
 - Better set & restore BFO handling
 - Memory handling modified for slow receivers
 - Nardeux T264 added
 - Thomson TRC294A added

=========================================================================
V1.1.1.1 - Internal
 - Receivers keeps theirs currents freq. setting when instructed to go 
   beyond boundaries. Previous code was setting frequency to boundary. 
 - Added RxFrqStp() function

=========================================================================
V1.1.1.0 - External - Published
 - Add RxChnDump()
 - Change the way the channel message are processed: quicked processing 
 - No more compatible with previous versions (API numbering change)

=========================================================================

V1.1.0.10 - External - Published
 - Better debug logging
 - TRC243 handle HF level autosend option now handled
 - Link keep alive and test can be configured through registry
   -> link test:  C_Test

=========================================================================

V1.1.0.9 - External - Published
 - Keepalive process corrected
 - Timeouts and retries can be configured through registry
   -> retries:  C_Retr (   1 < number <  38)
   -> polling:  C_Wait ( 150 <     ms < 499)

=========================================================================

V1.1.0.8 - External - Published
 - TRC243 corrected ISB filter selection and allows for BFO modification
 - RA6790 corrected ISB filter selection and allows for BFO modification
 - RA1792 corrected ISB filter selection and allows for BFO modification

=========================================================================

V1.1.0.7 - External - Published
 - TRC243 options decoding error: corrected
 - TRC241 doesn't have FM mode:   corrected
 - Filters configuration error:   corrected, error message added

=========================================================================

V1.1.0.6 - External - Published
 - Added 'ConnectRxBiteError' error state for RA6790

=========================================================================

V1.1.0.5 - External - Published
 - Added logical output control (not tested on EK085)

=========================================================================

V1.1.0.4 - External - Published
 - TRC243: Optimization
 - Added 'ConnectLnOpnError' link error state 

=========================================================================

V1.1.0.3 - Internal - Never published
 - Last 'to do' features and modifications
   - RA1792: Save/Restore original BFO before entering/leaving software 
	     Filters can be selected when in USB/LSB mode             
   - RA6790: Save/Restore original BFO before entering/leaving software 
   -  EK085: Save/Restore original BFO before entering/leaving software 
   - TRC243: Carrier frequency computation issue when recalling a channel 

 - Minor 'reconnect' issue while using TCP/IP remote control
   - Adapt the global wait time to the network latency as done with the 
     request/response handling

V1.1.0.2 - Internal - Never published
 - Last beta test version that includes all the supported receivers:
   - RA1792: Lots of bug corrected / last published version
   - RA6790: Lots of bug corrected / last published version
   - NRD535: Lots of bug corrected / last published version
             Added full channels setting/recall
             Allows users defined filters (3 max) for H-ROM Models
             Full Aux/Nar slot configuratio handling
   - TRC243: Lots of bug corrected / last published version
             Added full channels setting/recall
 	     Lots of bug corrected / last published version
  -  EK085:  New supported receiver 
             Added full channels setting/recall

V1.1.0.1 - Internal - Never published
 - Minor modifications due to many and many tests / adaptation cycles with 
   the TRC243 driver to verify that thenew model works whatever the used 
   setting: manual tuning/mode changes, memory selection, ....

V1.1.0.0 - Internal - Never published
 - Changed the way we handled input frequency. Now, the pseudo-carrier 
   is ALWAYS displayed in the main program view. The channelized frequency 
   is displayed in small digit in the alternate frame. Depending upon the
   selected mode (and receiver type) the displayed frequencies can differ
   from the displayer receiver one.

   Pseudo carrier is computed as follow:
    -AM:   Real carrier
    -SSB:  Real carrier
    -CW:   Real carrier
    -FAX:  Carrier that will give a 1.9Khz White
    -RTTY: Carrier that will give a 2.2Khz Mark

 - As our database works with pseudo-carrier dataset, tuning is now far 
   more easy and can be continuously done without jumping between
   frequencies when setting FAX or RTTY mode on the NRD535.

 -'AutoTune' option disappear replaced by the 'realcarrier' aligment 
   feature.

V1.0.0.8 - Internal - Never published
 - Adding channel memory access method

 - Corrects a nasty bug in the autofilter and automode option for manual 
   tuning

V1.0.0.7 - Internal - Never published
 - RA6790: Any filter change in the dialog will now be forwarded to 
   the receiver to be stored. In the previous versions, the user had 
   to enable this function.

V1.0.0.6 - Internal - Never published
 - First try to add the EK085 receiver driver
   Low performance due to the very bad EK085 software design:
    Reset of the front panel in modification mode when receiving remote 
    request
    No remote request handling while front panel is used (ie: flying 
    wheel being used)
    No signal level remote output

V1.0.0.5 - Internal - Never published
 - Correcting the filter table sorting method and uses a more generic 
   approach

 - Forwarding this modification to all the already written drivers

V1.0.0.4 - Internal - Never published
 - Resource renumbering due to program source restructuration

 - Code optimization

 - Correct a bug in the TRC243 filter configuration handling while in 
   the edition box

 - Preparing for the next driver: EK085 receiver

=========================================================================

V1.0.0.3 - External - Published
 - Process MsComm32.ocx and/or MsWinSck.ocx controls errors
   Error dialog box minor modifications
   Add 'ConnectObjectError' error when control is not find or
   can be registered

V1.0.0.2 - External - Published
 - Renaming 'DrvForward' method to 'RxForward' 
 - Forward mechanism optimizations

V1.0.0.0 - External - Published
 - No more  'RdXXX' default receiver methods and properties
 - Previous 'RxXXX' methods converted into properties
 - Many optimizations and bugs corrected
 - New connexion handling process with much more error details
 - Better emulated mode handling
 - Better Tune Follow handling
 - Tune follow now as an option
 - New driver for TRC243 (not delivered with default control)
 - BFO full control added
 - HF Attenuator level in dB added
 - HF Filter / Preselector control added
 - AGC and Squelch set control level added
 - New parameters for SMeter Event: native, dBV or S Point
       dBV as measured on my receivers

V0.9.5 - External - Published
 - Last version exporting the 'RdXXX' methods and properties

=========================================================================
